What is ScanMaster-ELM?

ScanMaster-ELM is an OBD-II / EOBD Diagnostic Tool for vehicle diagnostics compatible with OBD-II / EOBD standards and has been developed specifically for ELM Electronics’ ELM327 chip and supports all 10 OBD-2s defined in SAE J1979 Diagnostic modes $ 01- $ 0A and all communication protocols

ScanMaster-ELM Functions and Features:

Check engine light, obdpros, obd pros, OBDPros, scan tool, service engine soon light, ELM327, code reader, OBDPros, obd, obd2 scanner, automotive diagnostics, obd.

Automatically determines and identifies to the user the vehicle communication protocol under test.

Supports generic SAE J1979 (Mode $01) parameter identifiers (PIDs) $00 through $87.

Displays all or custom list of diagnostic data parameters supported by the vehicle’s OBD II controller with line graphs and meters.

View the condition of the vehicle system at the time when an emission related diagnostic trouble code was stored with Freeze Frame mode.

Read emission DTCs (and their common SAE descriptions) that cause the MIL to be illuminated. Plus, display the DTC number for the non-SAE defined DTC numbers and

descriptions that are reported by OBD II emission ECUs.

Supports over 4200 generic diagnostic trouble codes descriptions from SAE J2012 and over 3600 enhanced OBD-II codes, or a codes defined by the Original Equipment

Manufacturer (OEM).

Clear all emissions-related diagnostic information. (Mode $04)

Review the results of the oxygen sensor testing performed by the vehicle’s

powertrain control module with “Oxygen Sensors” mode (Mode $05).

Displays non-continuous diagnostic test results specific to the vehicle manufacturer (Mode $06 data) with the “Monitoring Tests Results” mode.

Reports vehicle’s continuously monitored emissions-related tests that have failed during a drive cycle and have not matured to indicate a diagnostic trouble code with

“Pending Diagnostic trouble Codes” mode.

Displays specific information applicable to the vehicle under test (VIN, Calibration ID,Calibration Verification Number, In-Use Performance Tracking).

Metric and English units of measure.

Shows Readiness for State Inspection.

Shows Fuel Consumption since version 1.3.

Drag Measurement since version 1.8.

Filmora watermark remover code 2020. Power and Torque Measurement since version 1.9.

Direct connection methods for USB, Bluetooth® and WLAN interfaces since version 2.0.

ScanMaster-ELM Support Protocols:

ISO9141-2
ISO14230-4 (KWP2000)
ISO14230-4 (KWP2000) slow init
SAE J1850 VPW
SAE J1850 PWM
ISO15765-4 (CAN bus) 11/250
ISO15765-4 (CAN Bus) 11/500
ISO15765-4 (CAN bus) 29/250
ISO15765-4 (CAN bus) 29/500

ScanMaster-ELM Minimum Platform and Software Requirements

You must have Microsoft Windows 98/ME/2000/XP/7 with Microsoft Internet Explorer 5.01 or

later or Firefox installed on your computer as well as Acrobat Reader.

Minimum hardware requirements:

. Pentium 200MHz or faster

. 64MB of RAM or higher

. CD-ROM or DVD-ROM Drive

. Free COM or USB Port

. For Bluetooth® or WLAN interface the computer must have Bluetooth® or WLAN

ScanMaster-ELM Free Download:

ScanMaster-ELM V2.1 Free Downlaod

ATTENTION TO WINDOWS MOBILE 10 USERS!LATEST WINDOWS MOBILE 10 UPDATE HAS A BUG (error Code: 0x8007000B) - YOU CAN'T INSTALL APP, IF YOU HAVE DEFAULT INSTALL LOCATION SET TO SD CARD! ATTENTION TO WINDOWS MOBILE 10 USERS!LATEST WINDOWS MOBILE 10 UPDATE HAS A BUG (error Code: 0x8007000B) - YOU CAN'T INSTALL APP, IF YOU HAVE DEFAULT INSTALL LOCATION SET TO SD CARD! What's new in this version:- Nissan Consult II bug fixes:- fixed some bugs- added Mitsubishi MUT-2 (pre-CAN) compatibility and connection profile- Chevrolet, General Motors, Opel and Vauxhall profiles with Extra sensors updated with new sensors. You need to apply this profiles again to add new sensors.:- added new connection profile for MAZDA SKYACTIV engines- added about 250 new parameters for Nissan Constul II protocol- DTC reading bugs fixedATTENTION TO WINDOWS MOBILE 10 USERS!LATEST WINDOWS MOBILE 10 UPDATE HAS A BUG (error Code: 0x8007000B) - YOU CAN'T INSTALL APP, IF YOU HAVE DEFAULT INSTALL LOCATION SET TO SD CARD! PLEASE, SET DEFAULT APP INSTALL LOCATION TO PHONE MEMORY, IF YOU'RE EXPECTING TROUBLES WITH DOWNLOADING CAR SCANNER!

Features. First of all – this app is really FREE.

Customizable multipage dashboard. Live data mode for advanced diagnostics. Supports multiple ECUs (with CAN protocols). Freeze frame reading and decoding. DTC (Check engine codes) reading, decoding and erasing. Massive fault code database for lookup of fault codes from different manufacturers.

Graph data. Fuel rate / MPG. 0-60 speed timings, brake timing, brake distance (based on speedometer). OBD protocol detection support.

Custom (extended) PIDs! Torque custom PIDs import supported. ECU self-monitoring test results. Submitted on Review title of LesOK on Solara and Avalanche with $3 ELM327 cloneDespite a 'bad ELM327 clone' error message using WIN10 and a $3 eBay ELM327 Mini, it works fine on both a Solara and Avalanche.

There isn't much for instructions, took a few tries, vehicle has to be running? The interface is generic looking, the available sensors seem incomplete, I can't find any live ABS/TCS/wheel speed sensor data, maybe only on the paid version? I wish it specifies what each version can or can't do. It gives you codes with a description but no explanation, you're left to search for more specific repair information, so it is helpful, but leaves me needing more. I'll keep looking.